3 in 1 T-Copper Kit for...
Electronic components kit for the Raspberry Pi. Kit Contents : 1 GPIO cable 40pin Female-Female 1 Breadboard 400Points 1 GPIO Extension Blue
- Out-of-Stock
Electronic components kit for the Raspberry Pi. Kit Contents : 1 GPIO cable 40pin Female-Female 1 Breadboard 400Points 1 GPIO Extension Blue
This 5V relay module with optocoupler allows easy control of electrical loads via a low-voltage control signal. Compact and practical, it features a single relay mounted on a PCB with screw terminals for quick and secure connections. Thanks to its built-in optocoupler, it provides isolation...
It is a serial interface E-paper display module, 4.3 inches, 800 × 600 resolution, with integrated font libraries, ultra low power consumption.
Increase the power of your projects using this battery holder capable of supplying 7.5V for conventional batteries and 6v for rechargeable batteries. The holder is terminated with bare wires so it can be directly soldered or connected to a screw terminal.
Features: Chip OV5647 Resolution: 5MP Photo resolution: 2952x1944 Viewing angle: 200° Focal length: 0.87mm Sensor cmos Aperture: 2.0 Cable length: 16cm Dimensions: 25x24x16.5mm
ACCESS: bit is a bolt-on/clip-on card for the BBC microbit that simulates an access gate. It includes a switch to turn on and off the built-in 3xAAA battery power, as well as an audible horn. The ACCESS: bit joins the micro: bit family of transport / crosswalk accessories, which also includes;...
Detect six distinct channels of visible light with this spectral sensor. Unlike normal RGB color sensors, with the AS7262, you'll get six bands of color readings that roughly translate into red, orange, yellow, green, blue and violet. The two built-in white LEDs allow you to illuminate...
The SN-390 Adjustable Bracket is specifically designed to clamp a printed circuit board and is ideal for PCB soldering and desoldering. Rigid metal frame with rubber stabilization pad, perfect for your project. Retractable stand with 2 adjustable handles to accommodate different board sizes up...
GPIO expansion card to double the number of available GPIO ports Designed specifically for the Raspberry Pi Pico Labeled female headers for attaching to your Pico, connection ports with labeled male headers 99% assembled - just glue the 4 rubber feet, no soldering required (as...
New version (v.3) of the controller designed by 8bitDo, the game controller manufacturer known for its quality of manufacture and its meticulous finishes A complete, retro and versatile game controller of high quality, inspired by classic video games and the colors of the SNES The...
Protective case with QWERTY keyboard Simply connect the holder to the underside of the official Raspberry PI 4 display holder and get a complete and compact workstation Connects to Raspberry Pi 4 via Bluetooth High battery capacity and can be recharged via Micro USB
ELEGOO R3 development board compatible with Arduino UNO REV3 Compatible with Arduino IDE projects Embeds the new version of the ATMEGA328P chip for control (identical to Arduino UNO R3) Easy development thanks to the naming of the female connectors: easier wiring ensured
Cooling fan size 310 with 4 screws and nuts. Dimensions: 30x30mm Not compatible with the Raspberry Pi 5
5MP night vision camera with 2 PCS infrared compatible PI3 and higher. Resolution 1080P.Adjustable focal length: 3.6mm. Diagonal angle: 60 DegreeComes with connection cablepower 3.3V.
With this cable, you can have a perfect fit. Each order comes with a cable, Pi camera not included.
The four batteries are connected in series, for a nominal power of 6V DC. - ON/OFF switch to control the power supply - Battery type: AA- Includes a removable sliding cover- 12.70 cm tinned wire and square configuration
The Pi T-Cobbler Plus GPIO Breakout for Raspberry Pi B+ is a T-shaped GPIO extension, allowing you touse a solderless breadboard with your Raspberry Pi B+. Simply connect your Pi T-Cobbler Plus (assembled) to your solderless breadboard, then connect it to your Raspberry Pi via its GPIO I/O...
This expansion board connects to a Raspberry Pi Zero or Zero W via pogo pins to provide a full-size USB Type-A connector.You can turn a Raspberry pi zero or Raspberry pi zero W into a U drive via the P4wnP1 project (https://github.com/mame82/P4wnP1), and also use it as a BadUSB device)....
A 16mm lighted button, ideal as a power button for picade X hat or simply for situations where you need a small lighted button.
This is an expansion board designed for micro: bit. It consists of a motherboard socket, 18650 battery socket, USB power interface, 3-5v external power interface, 4 programmable RGB lights, buzzer, I2C interface, WIFI camera serial port, motor interfaces of all kinds. It can also be connected...
Official Raspberry PI 4 LCD touch screen stand This official screen holder has been specially designed to house the official 7'' screen of the foundation Raspberry Pi, as well as the Raspberry PI. Black in color, this screen holder will bring the necessary protection to your touch screen.